ITAG4 SP

使用指导

设置设备

  • You need to configure ITAG series data loggers before starting recording, please follow steps below to configure an ITAG4 data logger.
  • TempSen provides pre-configured ITAG4 data loggers, please contact sales@tempsen.com for more details

拖放配置文件设置设备

 

  • 连接记录仪至计算机USB口，连接成功后LCD显示“USb”(USB)
  • 您可以从如下所示在线工具下载配置文件（.cfg格式)
  • 将配置文件保存至记录仪生成的可移动磁盘"TempSenDisk", 请不要打开或者尝试运行配置文件

  1. 使用TempSen Express软件设置设备

  • 打开TempSen Express
  • 进入“设备”页面
  • 将USB记录仪连接至计算机USB口，稍等片刻，已成功连接的设备将会显示在当前页面
  • 选择你需要进行设置的设备
  • 选择你所创建的配置文件
  • 点击“设置设备”按钮将所选的配置应用至选择的设备
  • 设置完成

 

  1.

设置设备后

LCD

 设备状态

设备USB连接中

设备断开USB连接后

手动启动(启动延时)

等待按键启动记录

自动启动

记录仪会在预设自动启动时间自动开始记录，无需任何按键操作

开始记录

  • 按住Start按键3秒
  • 开始记录后，LCD显示 “REC”

 

启动 启动延时 开始记录

If logger was programmed with start delay, LCD shows clock icon after starting logger.

 

停止记录

  • 按住停止按键3秒
  • 记录停止后，LCD显示“StoP” (Stop)

 

 

  • You could not stop a single use data logger within 30 minutes from the time it being started
  •  

下载数据

下载设备PDF报告

  • 连接记录仪至计算机USB端口，成功连接后，LCD显示 "USb" (USB) 或者USB图标
  • 在记录仪成功连接后, 记录仪会在数秒内开始自动生成PDF数据报告
    • 生成过程中，LCD会显示"PdF"
    • 生成过程中，LCD会显示"PdF"及生成进度 (ITAG4 series 4.0及以上版本)
    • 生成过程中，USB图标会闪烁 (ITAG4 SP)
  • PDF报告会生成在记录仪创建的可移动储存盘符(U盘)"'TempSenDisk"

 

 

 

 

使用TempSen Express下载数据

  • 打开TempSen Express
  • 在左侧导航菜单点击"设备"项目，进入设备页面
  • 连接数据记录仪至计算机USB端口，连接成功后， 设备LCD显示 "USb" (USB)或者USB图标
  • 选择您需要进行数据下载的设备
  • 在底部动作栏点击按钮开始将数据下载至TempSen Express

 

  • 已存储在TempSen Exapress中的数据文件将不会被再次下载

Error Codes

Please go to Error Codes for more information about error codes you may find on device LCD or PDF report created by loggers

FAQs 

General

Can I download data from logger after battery died?

Data in USB data loggers is always retrievable by connecting logger to USB port of computer to download data, even after battery was dead.

 

Do I need to re-program data logger to start new recording after last recording stops?

Multi-use data loggers like Tempod series should be re-configured for new recording after previous recording was stopped, but you could enable Repeat Start during configuration then after current recording stopped, you could start recording immediately by pressing Start button. Please note every time starting a new recording will erase existing data in logger, so always remember to download and save data in advance.

 

What does the lightening icon on LCD mean?

Some  loggers are shipped to customer with power system off status for power saving purpose, once user connects the logger to USB port, the power system will be activated and lightening icon appears on LCD which means logger starts consuming power, it is a remider for to use the logger ASAP.

 

Why can't I stop logger after recording began?

TempSen signle use loggers could not be stopped by pressing STOP button within 30 minutes after logger was started, this is to prevent from customer stopping recording mistakening when trying to start recording.

 

Can I re-program ITAG loggers after it's was started?

ITAG series data loggers are single use temperature data loggers, so it could not be programmed again after recording started, but you always could change the configurations before recording begins.

 

How can I know the expiry date of a single use logger, and can I use an expired logger?

You could find expiry date (EXP) date printed on single use loggers, and please DO NOT use a data logger already expired, otherwise power system may fail at any time during recording.

 

 

©TempSen Electronics Company  2023-08-23